海洋仪器网

Hi,

I have a Vaisala WXT520. In order to connect with CR10X, I am trying to program using Edlog 32 in LoggerNET with reference a manual, 'http://www.campbellsci.com/documents/manuals/wxt520.pdf'

But, I could not connect WXT520 with CR10X. Would you please check my CSI code.

Thanks for your support.

The following code is the CR10X program.

;{CR10X}
;
*Table 1 Program
01: 1.0000 Execution Interval (seconds)

1: Batt Voltage (P10)
1: 1 Loc [ Batt_Volt ]

2: If time is (P92)
1: 0 Minutes (Seconds --) into a
2: 1440 Interval (same units as above)
3: 30 Then Do

3: Signature (P19)
1: 2 Loc [ Prog_Sig ]

4: End (P95)

5: SDI-12 Recorder (P105)
1: 0 SDI-12 Address
2: 1 Start Measurement (aM1!)
3: 2 Port
4: 3 Loc [ Value1 ]
5: 1.0 Multiplier
6: 0.0 Offset

6: Excitation with Delay (P22)
1: 1 Ex Channel
2: 0 Delay W/Ex (0.01 sec units)
3: 50 Delay After Ex (0.01 sec units)
4: 0 mV Excitation

7: SDI-12 Recorder (P105)
1: 0 SDI-12 Address
2: 2 Start Measurement (aM2!)
3: 2 Port
4: 9 Loc [ Value7 ]
5: 1.0 Multiplier
6: 0.0 Offset

8: Excitation with Delay (P22)
1: 1 Ex Channel
2: 0 Delay W/Ex (0.01 sec units)
3: 50 Delay After Ex (0.01 sec units)
4: 0 mV Excitation

9: SDI-12 Recorder (P105)
1: 0 SDI-12 Address
2: 3 Start Measurement (aM3!)
3: 2 Port
4: 12 Loc [ Value10 ]
5: 1.0 Multiplier
6: 0.0 Offset

10: If time is (P92)
1: 0 Minutes (Seconds --) into a
2: 10 Interval (same units as above)
3: 10 Set Output Flag High (Flag 0)

11: Set Active Storage Area (P80)
1: 1 Final Storage Area 1
2: 101 Array ID

12: Real Time (P77)
1: 1220 Year,Day,Hour/Minute (midnight = 2400)

13: Average (P71)
1: 1 Reps
2: 9 Loc [ Value7 ]

*Table 2 Program
02: 0.0000 Execution Interval (seconds)

*Table 3 Subroutines

End Program

-Input Locations-
1 Batt_Volt 1 0 1
2 Prog_Sig 1 0 1
3 Value1 1 0 1
4 Value2 1 0 0
5 Value3 0 0 0
6 Value4 0 0 0
7 Value5 1 0 0
8 Value6 0 0 0
9 Value7 1 1 1
10 Value8 0 0 0
11 Value9 0 0 0
12 Value10 1 0 1
13 Value11 0 0 0
14 Value12 0 0 0
15 Value13 0 0 0
16 Value14 0 0 0
17 Value15 0 0 0
18 _________ 0 0 0
19 _________ 0 0 0
20 _________ 0 0 0
21 _________ 0 0 0
22 _________ 0 0 0
23 _________ 0 0 0
24 _________ 0 0 0
25 _________ 0 0 0
26 _________ 0 0 0
27 _________ 0 0 0
28 _________ 0 0 0
-Program Security-
0000
0000
0000
-Mode 4-
-Final Storage Area 2-
0
-CR10X ID-
0
-CR10X Power Up-
3
-CR10X Compile Setting-
3
-CR10X RS-232 Setting-
-1
-DLD File Labels-
0
-Final Storage Labels-
0,101,25478
1,Year_RTM,14143
1,Day_RTM
1,Hour_Minute_RTM
2,Value7_AVG~9,11381

* Last updated by: khkim on 2/16/2010 @ 6:04 PM *